![old craftsman table saw rip fence not square old craftsman table saw rip fence not square](https://i.ytimg.com/vi/B0IHnxhSZsg/maxresdefault.jpg)
It looks like hell and takes a few extra seconds to set up, but the end results are well within where they should be. So I marked and calibrated 1/2” increments right on the table, and use straight pieces of lumber clamped on as fences and a t-square for fine adjustments. Both ends are free-floating and you have to torque the handle sideways to get it to clamp onto the table, so there’s no way you’ll ever get it perfectly straight. The thing’s a monster and will cut through absolutely anything, but the 1970s-era fence and (can’t think of the word) movable handle thing leave a whole lot to be desired.
![old craftsman table saw rip fence not square old craftsman table saw rip fence not square](https://images-na.ssl-images-amazon.com/images/I/61bkcPMaQfL._SL1500_.jpg)
I have an old Delta table saw on long-term loan from a friend (heÂ’s a cabinet maker, and itÂ’s his #4 saw or something), and itÂ’s at least as old as I am. I'll just bring a ruler, move the fence, and see if the top and bottom are the same distance from the blade.Īpproach #2, if you don’t want to spend too much money: ghetto-rig your own fence system. My next stop is to go to Lowes/Home depot (possibly sears) and try the rip fences myself in person. The Porter Cable stuff was $200 for everything (compressor/2 nail guns/air tubes) and the miter saw was something like $60 bucks. I've done practically my entire house in all new molding, trim, and coving, with just those tools. I can attest to the 10" Delta compund miter saw and the porter cable "compressor/nail gun/brad nailer" in a box for moding, trim, and crown molding. It seems there's very little middle ground between cheap power tools that don't work well and the contractor-grade stuff.at least in my limited, newbie experience. Yeah.for weekend warriors it takes some hunting to find something of good value. (I don't have an exact answer for those yet.) If you buy smart, you can get everything you need for under $250. Currently, every tool shop is selling nail guns for cheap, and the generic, low-priced nail guns are more than sufficient for crown molding. Menards has a really nice "Tool Shop" branded compound miter saw that will do everything you want (even has a laser) for not much money. I'm sure craigslist is probably loaded with this stuff. I would still have saved quite a bit of money, even if I have to sell the tools cheap - or I could take some of the above suggestions and buy used equipment to begin with. I suppose I could just buy something with the intention of selling it after I'm done with it. I don't want to pay the $2-3k for somebody else to do it, but also don't want to pay out the ass just to get good cuts. I'm starting to look around for a decent-grade miter saw, stand, and nailgun to redo the trim and add crown molding in our house. all of the stuff you think you'll need to do to it short of actually cutting wood.
![old craftsman table saw rip fence not square old craftsman table saw rip fence not square](https://www.picclickimg.com/d/l400/pict/332534917051_/vintage-craftsman-table-saw-10322160-20-rip.jpg)
See if they'll let you change the blade (to see how hard it is) adjust the fence, pick it up and move it. I'd still try to spend time with it in the store. Of those, the JET saw from Home Depot looks to be the best. I was also considering getting a belt driven one, for noise concerns. But with nothing guiding the top of the fence, it locks down at some sort of angle every time.
Old craftsman table saw rip fence not square free#
The shitty one I have now, the bottom of the fence slides onto a rail, which is good, but the top is just free floating, and you push down a cam lever to lock it in place. I'd like to keep it below $300, and as cloase to $100 as I can.įrom what I am looking at with mysaw, it s not the fence itself that matters so much, but how it attaches to the table.